Error Codes AEG Washing Machine

Error code interpretation for the washing machine:

  E00: No Error - There is no error.

  E11: Water filling issue during washing cycle.

Check if the water supply tap is open.

Ensure proper water pressure.

Verify correct connection of the drain hose.

Inspect the water valve; replace or clean the filter.

Check the pressure switch and its wiring.

Inspect washing machine's wiring and terminals.

If needed, repair or replace the control module.

  E12: Difficulty filling water during drying mode.

Module fault; repair or replace.

Check washing machine wiring; repair or replace.

Inspect the hydraulic system of the pressure switch; replace if necessary.

Replace the electric valve if faulty.

Check water pressure in the apartment pipeline.

Ensure the drain hose is correctly installed.

  E13: Water leakage.

Check water supply tap and pressure.

Replace fill valve if defective.

Replace hydraulic system of the pressure switch if faulty.

  E21: Difficulty draining water within 10 minutes.

Clean or replace the clogged or bent drain hose.

Eliminate blockage in the pump filter.

Replace the drain pump.

Replace the pressure switch or main circuit board if defective.

  E22: Difficulty draining water; pump doesn't work for more than 60 seconds.

Clear blockage in the drain hose or replace the sensor.

Identify and eliminate defects in pressostat circuit wiring.

Replace pressure sensor.

  E35: Water overflow in the tank.

Replace the electrovalve.

Clean hydraulic system or replace the pressure switch.

Repair or replace the control module.

  E36: Heater protection level sensor malfunction.

Replace the sensor.

  E37: Faulty water level sensor.

Replace the sensor.

  E38: Blocking of the pressure receiver in the pressure switch.

Clean the hydraulic system or replace the pressure switch.

  E39: Defective water level sensor in the tank.

Replace the sensor.

  E41: Door not closed.

Check washing machine wiring and hatch lock contacts.

Securely close the door.

  E42: Problem in closing the door.

Replace or clean contacts of the hatch latch.

Replace the device for blocking the hatch.

  E43: Faulty triac of the power supply for the door hatch delay device.

Check washing machine wiring and hatch lock contacts.

Replace UBL or triac.

  E44: Violation of the door lock reading process.

Check washing machine wiring and hatch lock contacts.

Replace the hatch closing sensor.

  E45: Violation of the door lock reading process.

Replace UBL or control triac.

Repair or replace the control module.

  E51: Drive motor control circuit fault.

Replace triac or check and maintain circuit contacts.

  E52: No signal for the tacho generator of the CMA engine.

Check washing machine wiring on the TACHO chain.

Fix tachogenerator or replace the electric motor.

  E53: Motor Drive Triac Control Circuit Fault.

Detect and repair defects in the wiring.

Replace the electronic controller.

  E54: Malfunction of the reverse motor relay contact groups.

Replace the relay or electronic controller.

  E55: Motor circuit fault.

Rewind the engine or replace.

Check wiring and replace faulty wires.

Replace the board or repair it.

  E56: No signal from the tachometer generator.

Repair or replace the entire unit.

  E57: Current requested from the inverter has readings greater than 15A.

Check inverter circuit.

Replace the board or repair it.

Replace the engine.

  E58: Current requested from the inverter has readings greater than 4.5A, but less than 15A.

Check loading rate.

Check inverter circuit.

Replace the board or repair it.

Replace the motor.

  E59: Tachometric signal is absent for three seconds.

Replace wiring.

Replace the board or repair it.

Replace the engine or tachometer generator.

  E61: Water does not warm up to the desired temperature.

Find and replace defective area in the TEN control circuit.

Replace temperature sensor.

Replace heater.

Repair or replace the module.

  E62: Overheating of the water.

Fix wiring or replace it.

Install a new thermal sensor.

Check the circuit and replace burnt parts.

Repair or replace the module.

  E66: Faulty power relay resistor on the control board TEN.

Replace burnt parts.

  E68: Leakage of current through the heater to the ground.

Check wiring for breakdown voltage or replace TEN.

  E69: Resistor is in an inoperative state.

Check wiring and contacts.

Replace the defective part.

Repair the board.

  E71: NTC probe malfunction for washing.

Eliminate wiring defect.

Replace the thermal sensor.

Repair or replace the module.

  E72: NTC probe of the drying condenser is defective.

Eliminate wiring defect.

Replace the sensor or probe.

Repair the board.

  E73: NTC probe of the drying pipeline has failed.

Eliminate wiring defect.

Replace the sensor or probe.

Repair the board.

Check NTC contacts.

  E74: Operation violations in the NTC probe for washing.

Eliminate wiring defect.

Replace the sensor or probe.

Repair the board.

Check NTC contacts.

  E82: Wrong switch position when starting and restarting.

Repair contact tracks.

Replace burnt parts.

  E83: Switch

Comments: 0