Error Codes Asko Washing Machine

Error Codes and Descriptions for Washing Machine Models

E01 (W401/421/501/521/531) - Motor Fault (W640/650/660 Models)

Description: Common error indicating problems in the drive motor operation. Elements in the power circuit, such as the control triac, reverse relay, connectors, and motor, may be faulty. Verify the tachogenerator. If items are fine, replace the controller.

Conditions and Causes:

  • Faulty elements in the drive motor power circuit.
  • Control triac, reverse relay, connectors, or motor issues.
  • Check tachogenerator.

E02 (W401/421/501/521/531) - Water Inlet Fault (W640/650/660 Models)

Description: Error due to insufficient water in the tank. Causes include lack of water in the supply, damaged water inlet valve, clogged inlet path, faulty electronic controller, or a failed water level sensor.

Conditions and Causes:

  • Insufficient water in the supply.
  • Damaged water inlet valve.
  • Clogged inlet path.
  • Faulty electronic controller.
  • Failed water level sensor.

E03 (W401/421/501/521/531) - Draining Fault (W640/650/660 Models)

Description: Drainage issues. Check the connection between the electronic controller and drain pump. Verify mains voltage on the pump contacts during activation. If not, check pump, connectors, and controller. Examine the level sensor for specific models.

Conditions and Causes:

  • Connection issues between electronic controller and drain pump.
  • Lack of mains voltage on pump contacts.
  • Faulty pump, connectors, or electronic controller.
  • Incorrect sensor output voltage.

E04 (W401/421/501/521/531) - Insufficient Water Supply

Description: Error if the tank is not filled within a specific time. Causes include low water pressure or obstructions in the bay path (valve, filter, nipples).

Conditions and Causes:

  • Low water pressure.
  • Obstructed bay path.

E05 (W401/421/501/521/531) - Problems with Water Heating

Description: Error if water temperature is much higher than the set value. Check temperature sensor, heater, and circuits. Replace controller if necessary.

Conditions and Causes:

  • Water temperature much higher than set value.
  • Faulty temperature sensor, heater, or circuits.

E06 (W401/421/501/521/531) - Problems with Water Heating

Description: Error if water temperature hasn't reached the set value. Check heater and circuits. Replace controller if necessary.

Conditions and Causes:

  • Water temperature not reaching set value.
  • Faulty heater or circuits.

Door Lock Fault (W6651/6661) - Locking Fault

Description: In most cases, reset involves reclosing the hatch. If unsuccessful, check hatch lock integrity and electronic controller.

Conditions and Causes:

  • Door of hatch not closed or hatch is open.
  • Intact hatch lock.
  • Faulty electronic controller.

Floaming (W6651/6661 Models) - Increased Pricing Fixed

Description: If error occurs, run "RINSE" program. Use detergents with low pricing and observe dosage to avoid future errors.

Conditions and Causes:

  • Run "RINSE" program.
  • Use detergents with low pricing.
  • Observe detergent dosage.

Over Fling (W6651/6661 Models) - Overfilling (W640/650/660 Models)

Description: Fixed water overflow level in tank. Check water fill valve, level sensor, and controller integrity. If discharge pump doesn't activate at overflow, check it.

Conditions and Causes:

  • Fixed water overflow level.
  • Intact water fill valve, level sensor, and controller.
  • Check discharge pump.

Termistor Fault (W640/650/660 Models)

Description: Defective temperature sensor. Check for open or short circuit.

Conditions and Causes:

  • Defective temperature sensor.
  • Open or short circuit.

Pressure Sensor Error (W640/650/660 Models)

Description: Malfunction of level sensor. Check sensor and connector connected to the tank.

Conditions and Causes:

  • Malfunction of level sensor.
  • Check sensor and connector.
Comments: 0